Design and Fabrication of Concentration‐Gradient Generators with Two and Three Inlets in Microfluidic Chips

A simple and low‐cost method for designing and fabricating concentration‐gradient generators with two and three inlets is proposed which can generate different concentration gradients at varying flow velocities. The microchannel structure was designed in S‐shape and left‐right symmetry. The concentration‐gradient generator was simulated based on the finite element method. The microchannels were processed on a computer numerical control (CNC) engraving and milling machine on poly(methylmethacrylate) substrate, and then two concentration‐gradient generators were fabricated by hot bonding technology. The results of experiment and simulation were compared to prove the feasibility of the method. Flow velocity was an important factor for generating different concentration gradients. The concentration‐gradient profiles of the generators with two and three inlets present approximately linear and quadratic curves.     

镍基高温合金锥筒形件拉深旋压成形机理研究

针对镍基高温合金因加工硬化严重成形时极易产生破裂和起皱等典型缺陷的问题,以锥筒形壳体类零件为对象,提出了一种由锥形预制坯经过真空固溶处理后拉深旋压成形锥筒形件的方法,并对其成形机理进行了研究。基于Abaqus/Explicit平台,建立了锥筒形件拉深旋压有限元模型,分析了成形过程中的瞬态等效应力、等效塑性应变、切向应力、壁厚及三向应变分布规律。结果表明:在旋压成形过程中,最大瞬态等效应力位于旋轮接触区及附近区域、最大瞬态等效塑性应变位于坯料口部;瞬态切向压应力最大值位于旋轮接触区,而瞬态切向拉应力最大值位于旋轮接触区附近的两侧区域。筒形段中部壁厚减薄,而坯料口部壁厚增厚。旋压成形试验表明,锥形预制坯经拉深旋压后可获得壁厚均匀的锥筒形件。     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

不同制样方法对直流辉光放电质谱法测定氮化硼中27种杂质元素的影响

讨论了3种制样方法对直流辉光放电质谱法(dc-GDMS)检测氮化硼中的Na、Mg、Al、Si等27种杂质元素的影响。3种制样方法分别如下所示:方法1,直接把氮化硼压在铟薄片上;方法2,把氮化硼压在铟薄片上后,再盖上一层铟罩;方法3,把压碎后的氮化硼放在针状钽勺上。在优化的辉光放电参数下对比了3种不同制样方法对基体信号强度的影响。试验表明:在方法1中,当氮化硼尺寸约为3mm×3mm,厚度小于1mm时,基体¹¹B的信号可达1.8×10⁷ cps;在方法2中,选择铟孔大小合适的铟罩,基体¹¹B的信号可达1.0×10⁷ cps;方法3获得基体信号强度比方法1、方法2高一个数量级。大部分元素在中分辨率下可获得较好的结果,而对于在高分辨率下也较难分离的元素,可选择丰度较低的同位素在中分辨率下进行测定,如Ge选择⁷⁰Ge⁺,Se选择⁸²Se⁺,Cd选择¹¹¹Cd⁺,Sn选择¹¹⁹Sn⁺,Ag选择¹⁰⁹Ag⁺,Pt选择¹⁹⁴Pt⁺。氮化硼中的杂质元素含量可通过样品片中待测元素含量减去来自于铟薄片或钽勺中该元素贡献的含量来计算获得。将样品平行测定5次,相对标准偏差均在20%以内。对于Al、Si、Ti等元素的测定,3种制样方法的测定结果基本一致;方法1、方法2中检测到的In含量较大,使得铟中的Ni、Cu对氮化硼的测定值影响较大;方法3由于钽中Fe、Cu的贡献导致氮化硼中Fe、Cu的检测值较大,但方法3获得的基体信号强度大,可降低部分元素的检出限,如Cr、Mn、Ga、Ge等。综上所述,方法3为优选方法。     

Pull out of FRP reinforcement from masonry pillars: Experimental and numerical results

In this paper, debonding phenomena between carbon fiber reinforced polymer (CFRP) strips and masonry support were investigated on the basis of single-lap shear tests, considering different dimensions of the bond length. To capture the post-peak response of the CFRP–masonry joint, the slip between the support and the reinforcement strip was controlled using a clip gauge positioned at the end of the reinforcement. The tests were simulated by means of a finite element model able to capture the post-peak snap-back behavior due to the failure process. The numerical model is based on zero-thickness interface elements and on a proper non-linear cohesive law. The comparison between experimental and numerical results was performed in terms of overall response, measured by both the machine stroke and the clip gauge positioned at the free end of the reinforcement. The cases of effective bond length greater and lesser than the minimum anchorage length, suggested by the CNR Italian recommendation, were considered.     

Ti-6Al-4V电弧熔丝增材轧制复合制造的有限元模拟

增材制造过程中由于在凝固及随后的冷却阶段易产生残余应力,从而影响部件的成形和使用。在增材过程中引入轧制工序,可望降低宏观残余应力,从而降低部件的变形。本文通过建立Ti-6Al-4V钛合金电弧熔丝增材与层间轧制复合成形过程的有限元模型,研究圆柱形轧辊条件下不同压下量对部件温度、应力、应变及残余应力分布的影响规律。结果表明,层间轧制可显著降低沉积层金属中的残余宏观应力；同时降低对基板的整体应力。采用圆柱形轧辊并增加压下量可显著降低宏观残余应力,还可以通过塑性变形改变材料的微观组织,提高材料性能,为复合增材工艺的优化指明了方向。     

基于DEM的振动筛筛孔形状对潮湿原煤筛分效果影响的研究

随着原煤含水量的增加,引起原煤颗粒间相互粘聚,影响振动筛筛分效率。基于离散元法,运用EDEM软件模拟了潮湿原煤颗粒在圆形筛孔、方形筛孔和矩形筛孔的筛分过程,并且以筛分效率和阻碍粒排出率为衡量指标,对振动筛筛孔形状影响潮湿煤筛分效果进行了研究。结果表明:在筛孔名义尺寸相同的情况下,潮湿煤在矩形筛孔筛面上的筛分效果最好,方形筛孔次之,圆形筛孔最差。     

A comparison of transformation methods for evaluating two‐dimensional weakly singular integrals

Accurate numerical evaluation of integrals arising in the boundary element method is fundamental to achieving useful results via this solution technique. In this paper, a number of techniques are considered to evaluate the weakly singular integrals which arise in the solution of Laplace's equation in three dimensions and Poisson's equation in two dimensions. Both are two‐dimensional weakly singular integrals and are evaluated using (in a product fashion) methods which have recently been used for evaluating one‐dimensional weakly singular integrals arising in the boundary element method. The methods used are based on various polynomial transformations of conventional Gaussian quadrature points where the transformation polynomial has zero Jacobian at the singular point. Methods which split the region of integration into sub‐regions are considered as well as non‐splitting methods. In particular, the newly introduced and highly accurate generalized composite subtraction of singularity and non‐linear transformation approach (GSSNT) is applied to various two‐dimensional weakly singular integrals. A study of the different methods reveals complex relationships between transformation orders, position of the singular point, integration kernel and basis function. It is concluded that the GSSNT method gives the best overall results for the two‐dimensional weakly singular integrals studied. Copyright © 2002 John Wiley & Sons, Ltd.     

风险树分析在钻井工程事故中的应用

结合概率统计知识，利用风险树分析引发钻井工程事故的顶事件，重点讨论各底事件的相互联系及对系统的影响程度，从而寻找系统的漏洞，分析顶事件的发生概率，在此基础上采取相应的纠正措施，为最大程度地减少钻井工程事故的发生及其损失提供理论依据。     

水力射孔对套管强度的影响研究

水力射孔技术是一种新型的完井方式，深穿透水力射孔技术辅助定向水力压裂可以实现油气层改造和油气井增产。但是，水力射孔套管会在孔眼处造成应力集中，使得局部应力过大而削弱了套管和水泥环的强度，可能会影响套管的使用寿命。因此，文章利用有限元软件建立了射孔套管的三维有限元模型，分析了水力射孔后套管管体的应力分布，重点研究了水力射孔参数-孔密、孔径、孔深、射孔方位角等对套管强度的影响规律。分析结果表明，沿着最大水平地应力方向深穿透水力射孔，选择合适的孔密、孔径可将射孔对套管的损害降至最小。研究结果为提高水力射孔完井设计水平提供了一定的参数依据。